Hey all my 3a92 brethren, I might have briefly mentioned it elsewhere but this one deserves its own thread.
It's been over a year in development and machining but we finally have lightweight...
Hey all my 3a92 brethren, I might have briefly mentioned it elsewhere but this one deserves its own thread.
It's been over a year in development and machining but we finally have lightweight...
Super-Basic Quick Mirage Brake Check
(there's more to a thorough check than this...but this is a good start)
Jack up the car and remove a front wheel. This is what you'll be looking at...
...
I stole this from their facecrack page 18582
18583
https://gearsmagazine.com/magazine/tips-and-tricks-jatco-cvt-diagnostics/
Tips and Tricks, Jatco CVT Diagnostics
https://gearsmagazine.com/magazine/jf015e-common-issues/
1 Start the engine and warm up the CVT fluid to 50ºC (122ºF). Confirm CVT fluid temperature by checking FLUID TEMP in the Data Monitor.
2...
14810
14811
Alright, I got a package from DeatschWerks last night! They pack everything up nice for you after testing is done.
13961
Inside was my paper report, the injectors, and some 'super lube...
I sent the injectors off to them shortly after the last message I posted up. I just got a call from them today. The testing is done and they are shipping the injectors back along with the report. ...
To install my new front grill, i had to remove my front bumper:
It´s a quick 10 minute job you can do in your driveway.
There are 3 clips in each wheel well ( Picture 1 )
4 10 mm Bolts on top...
I think if you remove that bolt in the middle of the photo of your timing chain cover, a hole will be uncovered which will allow you to insert a thin rod to hold the cam chain tensioner retracted....
It looks to me like #1 is a spring loaded plunger that pushes against the chain guide / tensioner.
13643
As stated before, Loren did have some issue removing the crank pulley with his impact gun. Personally, I have a strong impact gun. I was confident it would have the torque to remove the bolt, and it...
Selecting a tank
Alright, let's start picking out parts! Again, let's start with the tank and move forward towards the engine.
The tank is well… a tank. It holds the nitrous oxide and without...
I think we need to go over the whole system in a bit more detail to see what we’re looking at. The first post went over the brief overview, but there is obviously a bit more to it when you are...
Alright, so the first step we need to look at is weather we want to go with a dry or a wet nitrous setup. All this really means is are you going to shoot just nitrous into your intake (dry), or are...
Here's the Engine Overhaul/Camshaft Removal DIY, from the 2015 Mitsubishi Mirage Service Manual:
13356
13357
13358
13359
13360
13361
13362
13363
13364
Yes, it can lock properly to both clockspring & ecu. You need to open socket's lock before insert the pins.
I think all mirage have same ECU, surprisingly they have same ECU for some mitsubishi...
But apparently others do.
Sometimes new and interesting ideas come from an open exchange without someone telling another what they can and what they cannot discuss.
I personally try to avoid...
Some of us want to know what things weigh. Be it for performance or fuel economy or just general geekiness, we want to know!
That's what this thread is for. If a moderator wants to try to keep it...
Here is a screen shot I took of ETACs decoder a while back showing you can change the tire circumference.
12876
Loren's answer is in this post:
Sometimes folks don't have time to go through all posts to find a little tidbit of info, or they are having a hard time searching for one reason or another. ...
Maybe this guy will ship to you?
https://www.ebay.com/itm/2014-2015-MITSUBISHI-MIRAGE-1-2L-ENGINE-MOTOR-EXHAUST-MANIFOLD/263755426375?hash=item3d690c6a47:g:2TwAAOSwi0RbISoR#shpCntId#shId
Could...
It does... and it doesn't.
Definitely has a nice quality pillow ball on the top front strut mount. And that mount is designed to be camber adjustable. The problem is that the allen-head bolts at...
Heres the latest from NST:
"Thanks again for sending us your OEM pulleys and thank you for all the
hard work on your end in trying to get a group buy together with your
forum members, we...
Hi,
I finally got around to installing 2017+ Front brakes on my 2015 Mirage.
Parts needed:
2017+ front brake caliper bracket
(you do not need the actual caliper, only the bracket. It may be...