Polyurethane end link Gourmet:
Energy Suspension - part # 9.7105R
Polyurethane Sway bar bushings (18mm):
Energy Suspension - 9.5122
Prothane - 191170 (Standard Grease Fitting)
191202 (90...
Polyurethane end link Gourmet:
Energy Suspension - part # 9.7105R
Polyurethane Sway bar bushings (18mm):
Energy Suspension - 9.5122
Prothane - 191170 (Standard Grease Fitting)
191202 (90...
Since gas prices are getting costly, I decided to put a grill block and underbody tray.
Grill Block
For the grill block, replace the stock grill with an aluminum mesh, and you can cover it with...
Correction: our bars is 18mm. Just installed the prothane bushings on the stock sway bar and it fits very well.
Prothane / Energy suspension Polyurethane bushings Sway bar upgrade
See images for parts list I compiled.
Tools required (sway bar bushings installation) :
12mm standard socket and deep socket...
I upgraded the Swaybar rubber bushing to prothane polyurethane
I will be uploading a tutorial soon on youtube with test drive video.
End links will be installed in a week. End link part is still...
Selling New headers for Mirage 2017+ MCC engine design. It will not fit previous generation.
3-1 efficient collector design
6+ HP gain
Engine would sound a little louder
Improve gas mileage ...
I installed a new set of powerstop rotors.
Rotor Part # POWER STOP JBR1762XPR
Ceramic brake pads part # CENTRIC 10517310
The new rotors are significantly lighter. Compare it to the weight of a...
Installed my new brake pads at 97,500 Km with the Powerstop Z23 Carbon Ceramic Pads. The brake pads is noticeably better than stock. It has better bite when braking. The brakes feels stronger when...
I changed the CVT fluid at 48,000km without the filter change (drain and refill method). At 90,000km, I have changed the fluid again, installed a new auxiliary filter, cleaned the magnets and the...
Swapped to Speed daddy lowering springs to make the ride softer yet still lower than the stock height. Dont want to get stuck in winter with the coilovers and have an uncomfortable ride since fast...
Went today to the Mitsubishi dealer from where I bought the car for the first time to pick up my dad since his RVR is in service. I received wow reactions but also turning heads from the sales...
This car can take up to 30cm wheel spacer at the rear. The front can definitely take more. I rolled the fenders at the rear since it is rubbing too much with load/passengers at the rear which may...
https://youtu.be/eJrnPP_ltlE
https://youtu.be/eJrnPP_ltlE
Front speakers have been upgraded to JBL GTO 629 since the GX602 at the rear is just too good. Whats best about this is that the there are some tones that the stock speaker dont produce or its...
I found a winter tire set for $25 for all on kijiji, with a considerable rust on it and 3 seasons left from the tread but its hard to turn down an offer.
My setup now is 185/65/14 with 3 mm hub...
New k&N Cold air intake mod
https://youtu.be/vlOrbqsvK3U
You can hear the mirage growl in the video with stock exhaust setup.
Parts needed:
K&N RG-1001RD Universal Chrome
As you can see in this video, I can flex the axle easily with my bare hands and it has a lot of play/movement and thats why a sway bar is highly recommended to increase the stability and safety at...
Here are the pictures of the rear diffuser. I am planning to build a flat tray just after the rear axle to the rear diffuser to maximize the effectiveness of the diffuser.
https://ibb.co/crdf9d...