Engine rpm slightly up and down when idle. It's getting worse when in D or R, with AC running, without pressing the throttle...in normal condition the car will move slowly, but in this case it'll...
Type: Posts; User: FreeYourSOUL
Engine rpm slightly up and down when idle. It's getting worse when in D or R, with AC running, without pressing the throttle...in normal condition the car will move slowly, but in this case it'll...
Same problem here, it's my Mitsubishi Xpander. Throttle body and sparks plug are clean, updated the ECU's firmware, recalled the fuel pump but no result.
It's noticeable from exhaust sound and...
First remove the chrome, there are clips on the back. Then pry the face out.
Love the sharptone's sound.
23132
Yes, basically the same process, You only need 3 components as I said above.
23124
23125
Hi @allrock, I was able to add speed alarm indicator.
Solder the yellow 3528 LED on front side. 1.5Kohm 1206 resistor and 40V 1A SOD-323 Schottky Diode on back (see my previous picture).
...
You can add the LED, some resistors, and LED driver (transistor) in red circles.
23116
Mine also has 4 LEDs for the gauge, the 4th LED is off because I messed up with the resistor. I did correct that later after made the video.
The center LED is for single eco indicator. It should...
The eco gauge shows us how economic is our driving, more mpg more green light on. But when we drive aggressively, less mpg, the orange light comes on.
Unlike average mpg on MID, it works instantly.
No, i'm doing it as hobby.
Hi, I try to add some missing LEDs on my cluster. I soldered some LEDs, resistors, LED drivers, & enable the Eco Gauge in ETACS.
The Eco Gauge is on, but only top LED is bright, the rest are...
Change cluster backlight to white and add cruise control LED.
23094
https://youtu.be/nW9rtPH9wh8
Didn't like all white LEDs, change back the MID LEDs to orange, change all yellowish green LEDs...
Hi @attrage 2020, can You help me to confirm what marking on this diode?
23055
Hi, I did have same KOS error indicator in my Mitsubishi Xpander. I can clear it by touching the start button with key fob then push it.
I don't know if it can be done with Mirage, but You can try...
Same with mine. I checked there are blank space for capasitor and resistor behind speed warning LED.
In circuit diagram there's no page for speed warning so I don't know what else missing.
...
Hi, some of us already successfully to enable factory cruise control but no indicator light on meter cluster.
Thanks to @pandafool171 for the clues, I managed to add the cluster's missing LED on...
Hi, I received the transistor today. It's small about 1×1.5mm with G8 marking.
22950
22951
Can You confirm if this is the right one?
If You don't have plan to lower your vehicle go with Ultra Racing. It has lifetime warranty, it won't be a problem even if it's fail.
Yes, that's mine.
The Pro 9000 is 5800K, less white than 6000K D5S.
On previous post I said that the Pro 9000 less uniform than old ultinon. Just want to point that.
Just read this thread, have You try to add some load resistors?
https://youtu.be/nU87VGnwedI
Top is Chinese D5S LED in Mirage's 2017 projector.
Bottom is Philips Pro 9000 H4 in Xpander's halogen reflector..
It prevent dust to enter the reflector.
It didn't break. Someone sold the pro 9000 cheap, so I bought it and gave my ultinon to my brother.
It's not flickering.
Hi, I used philips ultinon H4 before and now I'm using philips pro 9000. Personally I prefer ultinon, since the LEDs position 100% like halogen bulb, it produce more uniform light than pro 9000. The...
No, thats a notch on socket body to identify which is top or bottom.
#1 & #2 are for low & hi beam, cut the wires and each (+) goes into 8 pins connector. Leave the (-) of hi beam.
The 2 pins...
What type of bulb?