Search:

Type: Posts; User: Sipperofgas

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. 1 packet is enough for both front sides with some...

    1 packet is enough for both front sides with some left over. BTW the Rockauto kit (Quietmaster brake pads and rotor) come with a Quietmaster packet of brake grease which I have for next time.
  2. Updated the thread title to reflect the...

    Updated the thread title to reflect the discussion of grease. I too used the brake grease available in those small sized packets sold in Autozone.
  3. I went with the PS kit from RA. Very quiet, but...

    I went with the PS kit from RA. Very quiet, but might be just because it's new.
  4. Is this car the easiest to change front brake/rotors ? + rubber grease discussion

    Took me about 1 careful hour. The hardest part was getting the wheel lug nuts off. There are just 2 guide bolts barely tightened on holding the setup together. Unscrew those and you have access to...
  5. Damaged subframe. :eek:

    Damaged subframe. :eek:
  6. Close ! +400

    Close ! +400
  7. The only additional damage was under the front...

    The only additional damage was under the front bumper, some clips, and some metal underside cover thing between the front bumper and the oil pan (oil dripped form it during changes). Somehow the...
  8. Dude it could have been worse!

    Dude it could have been worse!
  9. Hit a jack stand at 55mph check this Dmg out

    You can see the axle leaking thick coffee colored fluid. And the oil pan has a huge dent in it about 1” across and maybe .75” deep. Do you guys think there’s enough space in the oil pan to not have...
  10. I have the car in the garage so I might as well...

    I have the car in the garage so I might as well check.
  11. Well the rattle is still there! It's not the...

    Well the rattle is still there! It's not the intake snorkle, and it's not the exhaust hangar. It's something in the interior. Some cable behind the plastic panels near the steering column is what it...
  12. Snorkel is zip tied down. It was loose, but i...

    Snorkel is zip tied down. It was loose, but i don't see how that noise can translate into the cabin. I will find out my next drive.
  13. i'll jack up the car and check some time this...

    i'll jack up the car and check some time this week. I'll check the snorkel today i think. It happens around 2.5-3k rpm.
  14. https://youtube.com/shorts/rm-aCd1IjIY I posted...

    https://youtube.com/shorts/rm-aCd1IjIY
    I posted a short video of the rattle.
  15. Omg we have the same thing. I was poking all...

    Omg we have the same thing. I was poking all around the steering wheel area since it seems that's where it's coming from. I just drown it out with music or radio.
  16. Replies
    48
    Views
    14,443

    That’s a picture of the low beam on uneven...

    That’s a picture of the low beam on uneven ground. I also dislike people who aim their beam too high or put hid lights into particularly bad halogen housings. Literally blinds you for a good couple...
  17. Replies
    48
    Views
    14,443

    Just an update: Happy with these projectors.

    Just an update: Happy with these projectors.
  18. Rattle/Buzz from under steering wheel under engine load.

    Under engine load around 4k rpm I have this noise that sounds like a wire bumping on plastic very quickly (almost buzz like). I have tried to find it for the past month, and cannot find it. It won't...
  19. Replies
    48
    Views
    14,443

    This is just before night time. I should really...

    This is just before night time. I should really take a picture in some of the pitch black areas I drive through.
  20. Replies
    48
    Views
    14,443

    look alright20321

    look alright20321
  21. Replies
    48
    Views
    14,443

    You can see that the mini gatling shroud doesn't...

    You can see that the mini gatling shroud doesn't fully cover the rear parts (rubber grommet and rear of projector are showing). You have to get full size shrouds to cover that I guess. I live in a...
  22. Replies
    48
    Views
    14,443

    https://imgur.com/oPNpqyy

    https://imgur.com/oPNpqyy
  23. Replies
    48
    Views
    14,443

    One headlight done. With the h4 adaptor plate...

    One headlight done. With the h4 adaptor plate there doesn't seem to be a way to aim the projector up or down. You can just rotate it a bit.
  24. Replies
    48
    Views
    14,443

    I finally got around to starting this project....

    I finally got around to starting this project. Took the plastic retainers off both inner fenders. Removed 6 10mm bolts (2 below grill). Pulled the top of the bumper off it's plastic clips. 3 bolts...
  25. Replies
    48
    Views
    14,443

    I've only baked headlights in the oven once, when...

    I've only baked headlights in the oven once, when i did the ACME kit on my Xterra. It seems intimidating but it really does soften up the glue to the point where you can pry them apart. I've only...
Results 1 to 25 of 39
Page 1 of 2 1 2