Search:

Type: Posts; User: Daox

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Thread: Hi everyone

    by Daox
    Replies
    9
    Views
    123

    Welcome to the site! It's great to hear your...

    Welcome to the site! It's great to hear your Mirage is being enjoyed.
  2. Replies
    28
    Views
    15,119

    Sticky: I'm sure a way could be figured out. A simple...

    I'm sure a way could be figured out. A simple way? I dunno about that. Just off the top of my head you got a slew of wires going to the clockspring that probably don't have a ton of slack. So there...
  3. Thread: Exhaust longevity

    by Daox
    Replies
    11
    Views
    259

    My 2014 has lived in salt every year of its life...

    My 2014 has lived in salt every year of its life and the only issue I've had is an annoying squeak during idle. It does have surface rust on it, but it is stainless.
  4. Replies
    39
    Views
    8,998

    The design changes included an alloy change on...

    The design changes included an alloy change on the tube, and a change to how they are welded to the end plates.

    If people would like to pre-order that would be fine by me!
  5. Replies
    2
    Views
    94

    Interesting find Foama! I just double checked...

    Interesting find Foama!

    I just double checked and if you go to the site I've used in the past (mitsubishipartswarehouse.com), they have no rear spring listed for a 2017!

    For a 2018 Mirage, they...
  6. Replies
    39
    Views
    8,998

    Alright guys, I just got the final quote back...

    Alright guys, I just got the final quote back from the manufacturer this morning. And I just sent of the purchase order to them. So, we got the revision done to the sway bar and they are on order! ...
  7. Replies
    28
    Views
    15,119

    Sticky: Alright guys, I just got the final quote back...

    Alright guys, I just got the final quote back from the manufacturer this morning. And I just sent of the purchase order to them. So, we got the revision done to the sway bar and they are on order! ...
  8. Replies
    152
    Views
    42,451

    Alright guys, I just got the final quote back...

    Alright guys, I just got the final quote back from the manufacturer this morning. And I just sent of the purchase order to them. So, we got the revision done to the sway bar and they are on order! ...
  9. Mirage compared to Tesla (Engineer Explained YT video)

    I think I've probably mentioned it before, but I like the youtube channel Engineer Explained. He puts out interesting info to me (I'm also an engineer). Anyway, in this video he compares a Tesla's...
  10. Replies
    25
    Views
    669

    Great review. I agree with pretty much the whole...

    Great review. I agree with pretty much the whole thing! I'll let others speak about the sway bar as I'm obviously biased.

    The next thing I'd love to do would be work on the over-assisted power...
  11. Replies
    152
    Views
    42,451

    I looked into it a little, but not that much....

    I looked into it a little, but not that much. Getting dimensions on different products isn't that easy unfortunately.
  12. If it's your car you can do whatever you want to...

    If it's your car you can do whatever you want to it. :encouragement:
  13. Replies
    8
    Views
    212

    Might want to check the alignment.

    Might want to check the alignment.
  14. Replies
    23
    Views
    689

    Sorry to see Mitsuko go, but glad to see you got...

    Sorry to see Mitsuko go, but glad to see you got Noodles!
  15. Thread: Whats this for

    by Daox
    Replies
    4
    Views
    194

    After 2014 they revised the motor mounts for...

    After 2014 they revised the motor mounts for whatever reason. Perhaps it was a cost cutting venture, or perhaps the new mounts reduce NVH. We'll probably never know.
  16. Replies
    152
    Views
    42,451

    Good news. I just sent new drawings off to the...

    Good news. I just sent new drawings off to the manufacturer to be quoted. The goal of these new revisions are to increase the life of the sway bar as there have been a few failures. I'm hoping to...
  17. Replies
    12
    Views
    330

    The forum upload is there to use as much as you'd...

    The forum upload is there to use as much as you'd like. We would much rather you upload them here so they never disappear. Its a common issue with forums. Nothing worse than looking up your...
  18. Replies
    31
    Views
    914

    Mark and Eggman are correct. I am out of stock on...

    Mark and Eggman are correct. I am out of stock on sway bars at the moment. I haven't ordered more because I've been working on improving the design. I'm very close to placing an order with my...
  19. Replies
    31
    Views
    914

    Woohoo, congrats! Nice deal too!

    Woohoo, congrats! Nice deal too!
  20. Replies
    28
    Views
    837

    Woohoo, congrats. :encouragement:

    Woohoo, congrats. :encouragement:
  21. Replies
    28
    Views
    837

    When doing P&G with engine off coasting (EOC),...

    When doing P&G with engine off coasting (EOC), you will typically use your clutch to bump start the engine. This definitely takes some practice, but once you get the hang of it it can be done very...
  22. Replies
    28
    Views
    837

    I've been meaning to do an air dam on mine for a...

    I've been meaning to do an air dam on mine for a while. It's an easy and cheap mod to do. That's probably where I would start if you don't already have the lower grill blocked on your car.
  23. Replies
    28
    Views
    837

    I have not been able to break 60 mpg without...

    I have not been able to break 60 mpg without using P&G in my Mirage. Especially at highway speeds, it just doesn't happen. If you can't P&G, you'll need to do a few aeromods to reduce the high speed...
  24. Replies
    4
    Views
    164

    Nice job. It's good to see it's an easy upgrade!

    Nice job. It's good to see it's an easy upgrade!
  25. Replies
    18
    Views
    703

    Will Running Out Of Gas Damage Your Car?

    I'm not sure how many of you have seen this channel, Engineer Explained but I really enjoy it being an engineer myself. He goes through several scenarios and explains pretty well how running out of...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4