Fuel Efficient 15-Inch Wheels and Tires
I'm running a 15-inch wheel/tire combination worth considering if you want to improve your Mirage’s appearance without sacrificing fuel economy. I've logged more than 45,000 miles on this setup and it appears to be as efficient as the OEM 14" wheels/tires.
This isn't the biggest set of wheels/tires you can squeeze under a Mirage, but it does represent a more aggressive looking and fuel-efficient alternative to the Mirage's undersized OEM wheels/tires.
Don't even think about changing your wheels and tires until you have had a 4-wheel alignment check done. If your Mirage has a rear wheel alignment problem, you want to have this corrected while you still have the OEM wheels/tires on the car to keep the warranty process simple. Most dealers WILL blame your aftermarket wheels and non-OEM size tires for your rear alignment issues. That's a load of BS...but why take a chance? Get an alignment check done FIRST.
Wheels....15 x 6.5 Konig Helium
Tires.......185-55-15 Bridgestone Ecopia EP422 Plus
Why did you choose these particular wheels/tires?
This was the lightest 15" wheel I could find with the right width, offset and reasonable price. The tires are among the most efficient (and longest-lasting) Low Rolling Resistance tires available. With fuel efficiency as a primary goal, this combination looked great on paper.
Read more details about how/why I selected these wheels/tires in the thread below:
Choosing Fuel Efficient 15-Inch Wheels and Tires
How much does this combination weigh compared to OEM wheels/tires?
How do these fit on the car compared to the stock wheels?
In my opinion, the fitment of these wheels can’t get much better on a Mirage. They sit out 1.25 inches closer to the edge of the wheel opening (compared to stock wheels), filling up the wheel well nicely. But they don’t stick out too far which might interrupt the aerodynamics of the car or cause rubbing issues. If anyone at Mitsubishi is paying attention, this is how OEM wheels should fit on these cars!
The diagrams below help illustrate the before/after fitment.
This image is from the website wheel-size.com. This gives you a rough idea of how these wider wheels eliminate the huge amount of fender clearance that the tiny stock wheels have...
This next image is from the website willtheyfit.com. They have a graphical tool that lets you see 2 wheel/tire combinations on the car at one time. Here’s what it looks like when you compare my setup to the stock 14" wheels/tires…
Here are a few photos so you can see that the wheels do not stick out beyond the fenders...
Do these tires rub anywhere?
These tires do not rub anything under any conditions (with stock springs). The front wheels can be turned lock-to-lock without any concern. This may be the widest wheel/tire you can run without experiencing any clearance issues.
What air pressure are you running in the tires?
I keep the tires at 50psi. The maximum rating on the sidewall is 51psi. After 45,000 miles and 9 tire rotations, the tires are showing absolutely no signs of over-inflation wear.
How has this wheel/tire affected your fuel economy?
I’ve averaged 51+ mpg for more than 40,000 miles on these wheels/tires. I only had the OEM wheels/tires on my car for 700 miles when it was new…so I don’t have any meaningful “before” mileage values to compare. But this wheel/tire combination has proven to be very efficient for the type of driving I’m doing (60% highway/40% city). I don't consider myself a hardcore hyper-miler. I just drive easy, minimize the AC usage, anticipate red lights and almost never exceed 60mph/3000 RPMs on the freeway. I don't do any "extreme" hyper-miling stuff like engine-off coasting or anything like that.
I may be getting the best fuel economy of any Mirage equipped with aftermarket wheels and tires.
What makes this an efficient wheel/tire combination?
Consider the following…
- This wheel/tire only weighs 1 pound more than a 14” factory alloy wheel and 165 Enasave
- The contact patch of a 185 Ecopia is identical to a 165 Enasave (details in this thread)
- The Bridgestone Ecopia EP422 Plus incorporates the latest advances in LRR tire technology
Do 185-55-15 tires affect the speedometer accuracy?
Yes...185-55-15 tires will cause the speedometer to read 2.5% below your actual speed.
This is because 185-55-15's are half an inch taller than 165-65-14's (a 2.5% difference).
When the speedometer reads 60mph, you are actually going 61.5 mph.
When my ScanGauge indicates 60mph, my Garmin GPS shows 61 mph.
TIP: Compare speedometer readings with different tires using this Speedometer Calibration Calculator
Do you have to adjust your mileage formula for these tires?
Yes…but it’s only a slight adjustment. With the slightly taller tires, the car is actually traveling a little bit further than the odometer indicates. When I read the number of miles I have driven for a tank of gas, I just add 2.5% to that number. If the odometer says I went 400 miles, the car really traveled 410 miles.
Does the car handle better with these wheels/tires?
These tires have the same contact patch as a 165-65-14 Enasave. Any handling improvement would mainly be due to the slightly wider stance of the new wheels and the different rubber compound and tread design of the tires (Ecopia tires are supposed to have improved wet/dry traction). To be honest, I drive like an old lady in this car…so I wouldn’t notice if these tires did provide a handling improvement. But others who have switched to a similar combination did report an improvement in handling.
Ecopia EP422 Plus tires are supposed to last 70,000 miles. Is that realistic?
They might last much longer than that the way I drive! I had a set of previous generation Ecopia tires on my G5 XFE. Those tires had a treadwear rating of 480 and had no problem making it to 70K miles. These newest Ecopias now have a treadwear rating of 640...or 33% higher than my older Ecopias.
UPDATE: These tires had 11/32" of tread when new. After 40,000 miles (and 8 tire rotations), they were all around 7/32". At this rate, I expect to get 90,00-100,000 miles out of them.
TIP: One way to reduce the cost of a new tire is by making it with LESS rubber. Tread depth is often overlooked when people are shopping for new tires. Did you know that OEM Enasaves only have 9/32" of tread when new?!? I put almost 30,000 miles on these Ecopias before they were worn down to the tread depth of a brand new Enasave.
Where did you buy these wheels/tires and how much did they cost?
Konig wheels are available from multiple online sources. But when you factor in the cost to ship/mount/balance wheels and tires, be sure to price them locally. Discount Tire is a national chain that sells Konig wheels, and they periodically run aggressive wheel and tire rebates...so that's where I ended up.
Discount Tire periodically runs a wheel promotion where you get a $100 Visa card for purchasing 4 wheels installed (installed means you pay for tire mounting/balancing when you buy the wheels). The $100 Visa card basically negates everything involved with the tire installation and all of the sales tax. This is a great deal because Discount Tire’s price on these wheels was only $4 more per wheel than Amazon!
The tires were also purchased during a promotion, where you received a $70 Visa card for buying 4 Bridgestones (this is now up to a $100 Visa card). Since the wheel purchase included tire installation, I only had to pay for the tires and sales tax. With the discount, these tires were actually cheaper than new Enasaves.
Discount Tire Cost
WHEELS (including required hardware)
15 x 6.5 Konig Helium Wheels (4 @ $89/each)..$356
Wheel Installation Kit (special lug nuts)....$ 15
TPMS Valve Stems.............................$ 32
Sales Tax....................................$ 33
185-55-15 Bridgestone Ecopia (4 @ $100/ea)...$400
Sales Tax....................................$ 30
Mount & Balance 4 tires......................$ 50
Prepaid Visa card with 4 new wheels.........-$100
Prepaid Visa card with 4 new tires..........-$ 70
Total After Rebates..........................$746 **
** I could have saved an additional $120 if I opened a Discount Tire credit card.
I sold my original wheels/tires for $450...so my actual cost for this upgrade was only $296!
If you don't care about maintaining your TPMS functionality, then you can save even more buy purchasing the wheels/tires from Discount Tire Direct and having them shipped to you. Here's an estimate of what this would look like (as of 2018)...
Discount Tire Direct Cost
15 x 6.5 Konig Helium Wheels (4 @ $99/each)..$396
Valve Stems..................................$ 12
185-55-15 Bridgestone Ecopia (4 @ $105/ea)...$420
Sales Tax....................................$ 61
Total After $320 Rebates.....................$569
Why would I want 15" wheels?
1. Big visual impact
Larger wheels (with the right offset) and tires will give your car a huge visual boost…especially on a Mirage where the OEM wheels/tires are small and the wheel offset too positive (the wheels look like they are pushed in too far under the car).
2. More/better/less expensive tire choices
165-65-14 is a very unusual size tire only used on the Mirage (in the US). If/when you need new tires, there are almost no choices available. If you consider an alternate 14” size (175-70-14), you may have a few more options. A more common 15” size (185-55-15) will give you a much greater selection of all types of tires...often priced lower than comparable 14" tires. To illustrate this point, here are the number of tires available at the Tire Rack in each size…
165-65-14 ........ 3
175-70-14 ........ 7
185-55-15 ........ 25
3. No down time if you need a new tire now
How many times has someone needed a single Enasave...just to find out that nobody stocks 165-65-14 tires? If you are on the road or in a jam and need a new tire NOW, you may be waiting days until a shop can order in a replacement. Or, you end up purchasing an entire set of 4 tires of an alternate size just to get going. Imagine a tire store that actually sells/stocks the tires on your car!
The real question you should be asking is this: Why would I want to keep my 14" wheels?
Do you really need new lugnuts for these wheels?
Yes. The factory lugnuts are too short/fat and won’t work. Just buy a Gorilla Wheel Installation Kit 21133HT (pictured below) which includes 20 high quality, small diameter, splined chrome lugnuts (12mm x 1.5) and the special socket for installing them. These kits are available on Amazon for $25. Discount Tire only charged $15 for the same thing.
TIP: Remember that your stock lug wrench will NOT work with these lug nuts. Always carry the special socket in the car. And make sure you have a wrench that will work with the socket. The end of the special socket is 19mm...so you need a 19mm socket to grip the end of it. This may or may not fit the stock lug wrench. I spent $10 on a short breaker bar and 19mm impact socket that I always have in the car. If I need to install my spare or remove my wheels, I'll just grab my breaker bar and socket setup and leave the stock lug wrench under the driver's seat.
They charged you $32 for valve stems? Isn't that a rip-off?
These valve stems are unique to the type of clip-on TPMS sensors used in the Mirage. They are not a typical rubber valve stem...even though they look like it from the outside. The end that goes inside the wheel has a special notch on the end of it (see image below). This is where the TPMS sensor clips on. Unlike some TPMS valve stems, you CANNOT remove these from your current wheels and reuse them. The only way to remove them from a wheel is to cut them out. $8 per valve stem may seem outrageous, but these cost more than $6/each even if you buy them from NAPA. Here's a picture of one...
What size hubcentric rings do I need with these wheels?
Mirage wheel center bore : 56.1mm (56.1 is the official size. The exact size I measured is 55.85mm)
Helium wheel center bore : 73.1mm
You will need hub rings with a 73mm outer diameter and 56.1 inner diameter (73/56.1). This is a common size hub ring you can find on eBay for $15. I prefer aluminum rings over plastic, but either will work. Hub rings are not absolutely required, but they are inexpensive and make installing the wheels much easier. They are well worth $15!
Note: Do not buy hub rings with a 73.1mm outer diameter, because they won’t fit into the Konig wheel bores without forcing them into place. Hub rings should fit into the wheel bore snugly…but you shouldn’t have to hammer them into place.
Where did you get Mitsubishi center caps for these wheels?
Konig Helium wheels come with blank center caps and flat, adhesive-backed “Konig” emblems that you install in the caps. Instead of using the Konig emblems, I found some Mitsubishi wheel cap centers (49mm) on eBay for $20. They fit perfectly in the Konig center caps. The black Mitsubishi emblem on a silver background looks great with the silver Heliums and gives the wheels an OEM look.
Here’s what I used…
Will the factory TPMS sensors work with these wheels?
Yes. My original TPMS sensors were installed in these wheels and they work fine. As long as the same 4 sensors are going back on the car, the TPMS light should not come on and nothing will need to be reprogrammed.
If you end up installing new TPMS sensors when you get new wheels/tires, the sensors will need to be registered with the car’s computer. Be aware that 99% of tire/repair shops out there will not be able to do this for you because Mitsubishi uses a proprietary TPMS computer. This programming is a dealer-only service which, in most cases, costs upwards of $100.
If you need new TPMS sensors, I highly recommend cloning the ID's of your existing sensors and having those ID's written onto another set of programmable TPMS sensors. If you do this, no further TPMS programming will be required (saving you a $100 trip to the Mitsubishi dealer).
NOTE: My dealer said they will not cover my OEM TPMS sensors under warranty because someone else mounted new tires on my car. Say what?!? Anyway...just be aware that once you swap your sensors to new wheels, your dealer may try to avoid responsibility for them if you have a sensor battery go dead within your 5 year/60,000 mile warranty. I don't think that's likely anyway...but just wanted to mention it here.
Are these wheels available in any colors besides silver?
Yes. Konig Helium wheels are available in silver, black or bronze.
I heard these wheels crack easily. What’s the deal?
Heliums are made using inexpensive casting methods. The result is a low-cost, lightweight, street-duty wheel.
Some have pushed the limits of Heliums by running them with sticky tires in track events, exposing them to loads they weren’t designed for. A few people cracked a wheel spoke doing this. Search the web for “cracked Konig Helium” and you’ll find some older threads on this topic. Konig doesn’t warrant these for off-road use because they are street-duty wheels, not forged race wheels.
Heliums have been sold for 10+ years and there are likely 100,000+ of them in use right now, but there aren’t any accounts I can find of one cracking under street use. That doesn’t mean they’re bullet-proof. Understand that an 11 pound cast aluminum wheel isn’t as strong as a steel or heavy cast wheel. If you hit a huge pothole, curb, etc. with a Helium, you should treat it like any other wheel and examine it for signs of damage.
Bottom Line: When used on the street, these wheels have proven to be reliable and are perfectly acceptable for 99% of us. Don’t take my word for it. Do your own research and decide for yourself.
Is there anything else I need to know before considering these wheels?
These wheels will expose your brakes for the world to see! The good thing is you can check your brake pads now just by looking through the spokes. The bad thing is that now everyone can see your crusty rotors. So you may want to consider cleaning up your rotors and hitting them with some paint. Same thing with your brake drums. The factory paint on brake components is really thin. So even if your drums/rotors look good now, take some time to put a layer of good high-temp paint on them. I painted everything and even did the calipers with G2 silver caliper paint. This is relatively easy when everything is new and clean.
Last edited by Top_Fuel; 06-05-2018 at 01:26 PM.
View my fuel log 2015 Mirage ES 1.2 manual: 51.3 mpg (US) ... 21.8 km/L ... 4.6 L/100 km ... 61.7 mpg (Imp)