Page 1 of 4 123 ... LastLast
Results 1 to 10 of 40

Thread: Developing an upper grill (mail slot) block 2014-2015 3d printed

  1. #1
    Administrator Daox's Avatar
    Join Date
    Jan 2013
    Location
    Germantown, WI
    Country
    United States
    Posts
    4,999
    Thanks
    2,892
    Thanked 1,804 Times in 1,017 Posts

    Developing an upper grill (mail slot) block 2014-2015 3d printed

    Name:  IMG_20181201_154013530.jpg
Views: 3022
Size:  98.1 KB

    This past weekend I took some time to put together a 3d printed upper grill block for my 2014 Mirage. I really like how it came out. So, I am going to share with you how I went about designing it and testing it out.

    First off, why would you ever want to block off your grill? There are two main reasons to block a grill off. The first is improved aerodynamics. Preventing air from going through the engine bay nearly always improves aerodynamics. The engine bay is very aerodynamically 'dirty'. Thus, pushing air around the car's body is advantageous because the body is more aerodynamically 'slippery'. Next, blocking grill area speeds up warm up times. It is currently December, and it has been in the mid 20s F in the morning here in Wisconsin. The upper grill block does help the car warm up a bit faster by not allowing as much cold air to pass over the engine. It also had the side effect of increasing the intake air temperatures of my warm air intake. Since less air is blowing around the engine bay, the warm air intake is able to suck up warmer air since the heat isn't being blow off the exhaust manifold quite as much. Since it is a small opening, the effects are not as pronounced as blocking the much larger lower grill area. However, this was a fun project to do, and it gives the car a bit of character with the different colors.

    That is all well and good, but the OEMs put a grill there for a reason Daox. Isn't it bad to block it off? It certainly can be. However, if we understand why there is a grill and how it was designed, we can better understand the modification. First off, the grill is there to allow cool air to the radiator for cooling. That is really its only purpose. We have to make sure enough air can get to the radiator to cool the engine. Lets also consider how the grill was designed. OEMs must design it for all conditions, so it is sized for a worst case scenario. This means running through a hot desert in the middle of summer with the A/C running. This is the opposite of my climate in winter, haha. Therefore, the grill is incredibly oversized for my environment, and I can take advantage of that and gain some of the benefits talked about above. I have no issues at all with my engine getting too hot on my daily commute to work. I always run my car with a scangauge installed which allows me to monitor my coolant temperatures. I can see when the radiator fan kicks on to cool things down. This never happens in winter, and very rarely in summer. That being said, this is for my climate, not yours. Higher ambient temperatures will require more air flow to cool your engine down and that must be taken into account when doing modifications like this. But, again blocking the upper grill is a very small area, so it doesn't have as big of an effect as blocking the lower grill area.

    Those are the pros and cons of blocking your grill off. So, lets get on to the fun stuff!

    This is my salty car. I checked out the grill on this thing and found that there are three vertical supports in the upper grill opening that we can use to attach things to. At this point I also measured things up, and got a rough idea of what I'm working with. For your reference, the opening is about 1" tall, and 24" wide.

    Name:  IMG_20181129_190150266.jpg
Views: 2735
Size:  102.8 KB



    Next up, I tested my attachment method. I figured a clip that goes around either side of those vertical supports would be plenty to hold it on. I 3d printed a test piece after measuring the supports up, and test fit it. To my surprise, the test piece fit perfectly, and the held the piece on quite nice. Typically these things take a few iterations, as you'll see.

    Name:  IMG_20181129_213700039.jpg
Views: 2653
Size:  95.0 KB



    Okay, so I got a working clip design, and rough opening dimensions. At this point I drew up the full grill block. I eyeballed how things fit with the tapering of the grill towards the ends, and went on the small size to make sure it fit. I had to split the grill block into 3 pieces so it would fit on my 3d printer. A few hours later, I had the first version of the grill block.

    Name:  IMG_20181201_103352526.jpg
Views: 2616
Size:  87.1 KB



    Time to test fit it! The clips worked great, they all lined up really nicely with the supports. However, the end pieces needed some work to fit the opening better. This was expected as I just eyeballed them. I also had to fix some issues with shrinkage and bowing in my parts. You can see the long parts look like the taper towards the ends. This is because as the parts cool on the printer, they shrink. I actually had to change materials because the first material I used shrunk too much and I had too many problems with it.

    Name:  IMG_20181201_103735107.jpg
Views: 2607
Size:  97.0 KB

    Name:  IMG_20181201_103742417_HDR.jpg
Views: 2508
Size:  97.8 KB

    Name:  IMG_20181201_103821373.jpg
Views: 2513
Size:  95.3 KB

    Name:  IMG_20181201_103915316.jpg
Views: 2448
Size:  95.6 KB



    So, back to the 3d drawing board. The next version filled out the ends a lot better. However, it still had a problem with the grill block not following the contour of the opening. It is a bit hard to see in the picture, but the grill block is sticking out, not laying flat against the grill opening.

    Name:  IMG_20181202_091035226_HDR.jpg
Views: 2546
Size:  97.1 KB



    The next version got a bit more curvature to it to bring it back in closer to the grill opening.

    Name:  IMG_20181202_091025872_HDR.jpg
Views: 2516
Size:  95.0 KB



    This is basically where I am at right now. There is a bit more tweaking to do. The pieces fit in really nice. They fit the opening great, follow the front contour of the car great. But, there is one thing that is bugging me just a little bit, and that is that they do not align to each other all that great. Its not super noticeable, but I want to add some alignment tabs between the pieces to keep them lined up to each other. Here is what I am talking about.

    Name:  grill1.jpg
Views: 4044
Size:  54.5 KB


    Custom Mirage products: Cruise control kit, Glove box light, MAF sensor housing, Rear sway bar, Upper grill block

    Current project: DIY Nitrous oxide setup for ~$100

        __________________________________________

        click to view fuel log View my fuel log 2015 Mirage DE 1.2 manual: 47.2 mpg (US) ... 20.1 km/L ... 5.0 L/100 km ... 56.7 mpg (Imp)


  2. The Following 8 Users Say Thank You to Daox For This Useful Post:

    Alex1a1f (12-04-2018),Cobrajet (12-04-2018),inuvik (12-04-2018),MetroMPG (12-07-2018),spork (12-12-2018),ThunderG (03-05-2019),Top_Fuel (12-04-2018),Tyrelirwin (12-04-2018)

  3. #2
    Senior Member
    Join Date
    Feb 2014
    Location
    Alberta, Canada
    Country
    Canada
    Posts
    193
    Thanks
    121
    Thanked 64 Times in 48 Posts
    looks great! I used tape...Name:  car.jpg
Views: 2466
Size:  91.7 KB

        __________________________________________

        click to view fuel log View my fuel log 2014 Mirage ES 1.2 automatic: 36.9 mpg (US) ... 15.7 km/L ... 6.4 L/100 km ... 44.3 mpg (Imp)


  4. The Following User Says Thank You to Tyrelirwin For This Useful Post:

    Daox (12-04-2018)

  5. #3
    Looks like you've got the same fog light block off plate delete kit like a lot of our cars have.

        __________________________________________

        click to view fuel log View my fuel log 2014 Mirage SE wussie cvt edition. 1.2 automatic: 37.7 mpg (US) ... 16.0 km/L ... 6.2 L/100 km ... 45.3 mpg (Imp)


  6. The Following User Says Thank You to Fummins For This Useful Post:

    Tyrelirwin (12-07-2018)

  7. #4
    Senior Member
    Join Date
    Feb 2014
    Location
    Alberta, Canada
    Country
    Canada
    Posts
    193
    Thanks
    121
    Thanked 64 Times in 48 Posts
    Daox- can you tell me a little bit more about (or point me to the relevant thread) your block heater 'port'?

    Fummins- The bulbs lasted longer than the glass, but not much longer. Pack enough snow/ice in there and aero is improved!

        __________________________________________

        click to view fuel log View my fuel log 2014 Mirage ES 1.2 automatic: 36.9 mpg (US) ... 15.7 km/L ... 6.4 L/100 km ... 44.3 mpg (Imp)


  8. #5
    Administrator Daox's Avatar
    Join Date
    Jan 2013
    Location
    Germantown, WI
    Country
    United States
    Posts
    4,999
    Thanks
    2,892
    Thanked 1,804 Times in 1,017 Posts
    Sure, check out my block heater thread here:

    https://mirageforum.com/forum/showthread.php/5783
    Custom Mirage products: Cruise control kit, Glove box light, MAF sensor housing, Rear sway bar, Upper grill block

    Current project: DIY Nitrous oxide setup for ~$100

        __________________________________________

        click to view fuel log View my fuel log 2015 Mirage DE 1.2 manual: 47.2 mpg (US) ... 20.1 km/L ... 5.0 L/100 km ... 56.7 mpg (Imp)


  9. The Following User Says Thank You to Daox For This Useful Post:

    Tyrelirwin (12-07-2018)

  10. #6
    Administrator Daox's Avatar
    Join Date
    Jan 2013
    Location
    Germantown, WI
    Country
    United States
    Posts
    4,999
    Thanks
    2,892
    Thanked 1,804 Times in 1,017 Posts
    I haven't had good luck getting an alignment tab working on these things. The problem is the parts are long and skinny. When you 3d print, its kind of like welding. The hot plastic / metal shrinks when it cools and you get part warpage, or they just don't adhere to the bed and the print gets messed up. It is exaggerated for skinny long parts. I've already switched materials to one that does not warp as badly, but its still an issue when you're trying to line things up that precisely. I'll likely have to get some new bed material to get this to work perfectly.

    That all being said, its really not that bad anyway, and I can just be a perfectionist when it comes to this stuff. The gap is maybe 1/16". I don't even notice it if I am not looking for it.

    So, in the mean time, I am going to start selling these if anyone is interested. The price will be $19.99 shipped to the US.

    Upper Grill Block - $19.99 shipped

    I still have a few prototypes that I'll sell for a few bucks more than shipping. If anyone is interested, shoot me a PM.



    Some more pictures:

    Name:  IMG_20181201_154013530.jpg
Views: 2329
Size:  98.1 KB

    Name:  IMG_20181202_090950535_HDR.jpg
Views: 2328
Size:  98.9 KB

    Name:  IMG_20181202_091002268_HDR.jpg
Views: 2349
Size:  96.1 KB

    Name:  IMG_20181203_072329178.jpg
Views: 2395
Size:  98.2 KB

    Name:  IMG_20181203_072344790.jpg
Views: 2183
Size:  93.8 KB
    Custom Mirage products: Cruise control kit, Glove box light, MAF sensor housing, Rear sway bar, Upper grill block

    Current project: DIY Nitrous oxide setup for ~$100

        __________________________________________

        click to view fuel log View my fuel log 2015 Mirage DE 1.2 manual: 47.2 mpg (US) ... 20.1 km/L ... 5.0 L/100 km ... 56.7 mpg (Imp)


  11. The Following 2 Users Say Thank You to Daox For This Useful Post:

    Top_Fuel (12-10-2018),Tyrelirwin (12-10-2018)

  12. #7
    Administrator Daox's Avatar
    Join Date
    Jan 2013
    Location
    Germantown, WI
    Country
    United States
    Posts
    4,999
    Thanks
    2,892
    Thanked 1,804 Times in 1,017 Posts
    I just got a new color in yesterday for someone who wanted a sapphire blue grill block. I started the print and it finished up over night. I'll get a picture of it on the car. It looks pretty nice in person. The picture doesn't show it as well.

    Name:  IMG_20190305_064746617.jpg
Views: 2241
Size:  28.7 KB
    Custom Mirage products: Cruise control kit, Glove box light, MAF sensor housing, Rear sway bar, Upper grill block

    Current project: DIY Nitrous oxide setup for ~$100

        __________________________________________

        click to view fuel log View my fuel log 2015 Mirage DE 1.2 manual: 47.2 mpg (US) ... 20.1 km/L ... 5.0 L/100 km ... 56.7 mpg (Imp)


  13. The Following 2 Users Say Thank You to Daox For This Useful Post:

    Eggman (03-05-2019),MacClyver (03-05-2019)

  14. #8
    Cool - waiting for the pic.

        __________________________________________

        click to view fuel log View my fuel log 2014 Mirage ES 1.2 manual: 63.2 mpg (US) ... 26.9 km/L ... 3.7 L/100 km ... 75.9 mpg (Imp)


  15. #9
    Administrator Daox's Avatar
    Join Date
    Jan 2013
    Location
    Germantown, WI
    Country
    United States
    Posts
    4,999
    Thanks
    2,892
    Thanked 1,804 Times in 1,017 Posts
    Here it is with a lot of sun on it. It actually looks darker than the pictures show.

    Name:  IMG_20190306_092258136_HDR.jpg
Views: 2159
Size:  97.5 KB

    Name:  IMG_20190306_092305841_HDR.jpg
Views: 2184
Size:  97.0 KB

    Name:  IMG_20190306_092327280_HDR.jpg
Views: 2183
Size:  96.9 KB


    I also took the opportunity to try out my new 3d printer bed material. Previously, the grill block fit up like the picture bellow. This is a picture from last night. It didn't fit good, so I setup the new bed and tried things out. It fits a lot better now. This also gives you an idea of the color when the sun isn't beating against it.

    Name:  IMG_20190305_173005236.jpg
Views: 2173
Size:  96.0 KB
    Custom Mirage products: Cruise control kit, Glove box light, MAF sensor housing, Rear sway bar, Upper grill block

    Current project: DIY Nitrous oxide setup for ~$100

        __________________________________________

        click to view fuel log View my fuel log 2015 Mirage DE 1.2 manual: 47.2 mpg (US) ... 20.1 km/L ... 5.0 L/100 km ... 56.7 mpg (Imp)


  16. The Following User Says Thank You to Daox For This Useful Post:

    MetroMPG (03-06-2019)

  17. #10
    Senior Member
    Join Date
    Feb 2014
    Location
    Alberta, Canada
    Country
    Canada
    Posts
    193
    Thanks
    121
    Thanked 64 Times in 48 Posts
    How about a 3D lower grille block? Any plans for that?


        __________________________________________

        click to view fuel log View my fuel log 2014 Mirage ES 1.2 automatic: 36.9 mpg (US) ... 15.7 km/L ... 6.4 L/100 km ... 44.3 mpg (Imp)


  18. The Following User Says Thank You to Tyrelirwin For This Useful Post:

    Daox (03-08-2019)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •