Results 1 to 4 of 4

Thread: DIY: Fixing a P0442 code (small evap leak / fuel pump housing crack) for $10

  1. #1
    Administrator Daox's Avatar
    Join Date
    Jan 2013
    Location
    Germantown, WI
    Country
    United States
    Posts
    4,999
    Thanks
    2,892
    Thanked 1,804 Times in 1,017 Posts

    DIY: Fixing a P0442 code (small evap leak / fuel pump housing crack) for $10

    Name:  IMG_20220206_152402391.jpg
Views: 1382
Size:  94.3 KB

    Background:
    Not long ago I noticed my check engine light pop on. Thankfully, I have a scangauge in the car all the time. So, I scanned it and found it was a P0442 code. This code says there is a small evap leak in the fuel system. Next step is obviously do a search on Mirage Forum! I found this thread. So, I take a look and sure enough that was my problem too. No way was I paying $900 for a fuel pump housing, so this is how I did it.



    Name:  IMG_20220206_151816168.jpg
Views: 1413
Size:  94.9 KB

    First, pop out the rear bench seat. Just pull up roughly in the center of each side. Its held down with a plastic snap connector. They're yellow in the image above. Once they've unsnapped you can pull the seat out.



    Name:  IMG_20220206_151822512.jpg
Views: 1315
Size:  95.7 KB

    Now, remove this cover. Three phillips screws and its off. Its got a foam gasket under it so it will probably require a bit of prying to get up.



    Name:  IMG_20220206_151924987.jpg
Views: 1331
Size:  97.8 KB

    Next, remove all of these connections. They're all pretty easy to figure out except the lower left one.



    Name:  IMG_20220220_151156132.jpg
Views: 1300
Size:  91.2 KB

    Name:  IMG_20220220_151259415.jpg
Views: 1318
Size:  88.5 KB

    On either side of the white plastic there is some hooks to pull back, then the white cap will up straight up.



    Name:  IMG_20220220_151606341.jpg
Views: 1363
Size:  91.5 KB

    Now, you can pull the white hooks apart and pull the black sensor straight up.



    Name:  IMG_20220220_151923364.jpg
Views: 1399
Size:  93.6 KB

    Time to get that retaining ring off. Use a big flat bladed screw driver and hammer to start wacking it. Mine is obviously rusty and it took a decent bit of work smacking it all around the circle. Eventually it slowly started to move and loosen up.



    Name:  IMG_20220220_152125758.jpg
Views: 1310
Size:  92.6 KB

    Pull the retaining ring off, and then you can pull the fuel pump assembly out of the tank. You'll need to tip it as you go so you don't spill a bunch of gas all over stuff.



    Name:  IMG_20220220_152505345.jpg
Views: 1313
Size:  81.5 KB

    With the fuel pump assembly on a bench, clean it up and find the crack. In my case, the crack went all the way through and it wasn't tiny. I'd say it was at least 1/32" / 1mm in width. You could easily see light through it.



    Name:  IMG_20220220_160102144.jpg
Views: 1347
Size:  79.0 KB

    Then hit it with some rubbing alchol and a rag, and also a toothbrush to get in the crack as best I could. Then I hit it with 180 grit sand paper and then rubbing alchol to clean it up to prep it for glue.



    Name:  IMG_20220220_160416514.jpg
Views: 1226
Size:  93.2 KB

    This is the stuff I ended up using to seal up the crack. Its JB Weld Plastic Bonder. It is apparently made to bond to nylon which is what I believe this plastic is. Its very slippery and obviously holds up to gasoline.



    Name:  IMG_20220220_160453185.jpg
Views: 1303
Size:  78.6 KB

    So, mix some up and slather it on and in the crack. I used my finger to mush it into the crack. I also put some on the back side of the crack in the hopes it would anchor better that way.

    You can let it cure or put it back in and let it cure in place (this might be a better option). I let mine cure the recommended 30 minutes. It was definitely not hard when I put it back in. However, I was running out of light, so in it went.

    I think its been about a week now since I did this. My CEL has stayed off and I just passed emissions. I'm not exactly sure how long it'll last, but there is no way I was paying $900ish for a plastic housing! Good luck to you if you try it out.


    Custom Mirage products: Cruise control kit, Glove box light, MAF sensor housing, Rear sway bar, Upper grill block

    Current project: DIY Nitrous oxide setup for ~$100

        __________________________________________

        click to view fuel log View my fuel log 2015 Mirage DE 1.2 manual: 47.2 mpg (US) ... 20.1 km/L ... 5.0 L/100 km ... 56.7 mpg (Imp)


  2. The Following 9 Users Say Thank You to Daox For This Useful Post:

    BigMW (05-27-2023),CROSSBOLT (03-03-2022),Fummins (02-26-2022),Grumpy Bear (01-22-2024),inuvik (02-27-2022),Macmoto (03-04-2022),MetroMPG (03-03-2022),R01k (05-27-2023),Top_Fuel (02-25-2022)

  3. #2
    Thanks for the detailed fix, Tim!

    Keep us posted.

        __________________________________________

        click to view fuel log View my fuel log 2014 Mirage ES 1.2 manual: 63.2 mpg (US) ... 26.9 km/L ... 3.7 L/100 km ... 75.9 mpg (Imp)


  4. #3
    Senior Member
    Join Date
    Oct 2021
    Location
    Whiteville, TN
    Country
    United States
    Posts
    256
    Garage empty: add car
    Thanks
    367
    Thanked 69 Times in 55 Posts
    Righteous repair!
    Karl

  5. #4
    Я R01k's Avatar
    Join Date
    Jun 2014
    Location
    US
    Country
    United States
    Posts
    544
    Thanks
    161
    Thanked 87 Times in 64 Posts
    Thanks for the walkthrough! I'm getting ready to check if my problem is the same, as I got this CEL a few days ago. How has your fix held so far?


        __________________________________________

        click to view fuel log View my fuel log 2014 Mirage ES 1.2 automatic: 37.6 mpg (US) ... 16.0 km/L ... 6.3 L/100 km ... 45.2 mpg (Imp)


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •