Fummins (06-13-2019)
That's possible. I worked on a denali that would hammer on the brakes out of the blue and the stabilitrac and abs lights would come on because of a bad front speed sensor. Usually speed sensors throw codes but not always.
I checked the wheel speeds in the freeze frame when the codes were thown and they were all the same. Could be sparatic, but that wouldn't explain the running lean code and the long crank to start. Might be 2 or 3 separate issues. I've seen abs and trac lights come on because of throttle issues before though.
__________________________________________
View my fuel log 2014 Mirage SE wussie cvt edition. 1.2 automatic: 37.7 mpg (US) ... 16.0 km/L ... 6.2 L/100 km ... 45.3 mpg (Imp)
__________________________________________
View my fuel log 2014 Mirage SE wussie cvt edition. 1.2 automatic: 37.7 mpg (US) ... 16.0 km/L ... 6.2 L/100 km ... 45.3 mpg (Imp)
Another update, I checked the brake lines last month and everything was good. Car hasn't had any issues until a few days ago. All the same codes came back.
C1396 engine torque input refusal
U0401 I forget communication code I think
P0137 02 sensor 2 low
P0102 AFS low
P0171 Fuel trim too lean
Car would idle low, hard to start. Had to hit throttle to keep running. I took it for a drive and it wouldn't rev past 3000rpm and felt like it was hitting a rev limiter. Transmission wouldn't shift. Car wouldn't go faster than 30-40kph. Check engine light, and traction control lights were on.
I checked the connector behind the kick panel and it looked like new. For real, it was pretty clean back there.=
I started doing a wiggle test and the engine would stumble when I wiggled the maf connector. Turned out one of the pins on the maf I replaced was bent. I'm not sure hth that happened. But I cleared the codes and couldn't get it to act up again. So fingers crossed I don't see this thing back for a while!
__________________________________________
View my fuel log 2014 Mirage SE wussie cvt edition. 1.2 automatic: 37.7 mpg (US) ... 16.0 km/L ... 6.2 L/100 km ... 45.3 mpg (Imp)
inuvik (07-12-2019)
How do you view the data from when the code was thrown? What sort of reader or data logger or whatever do i need for that?
__________________________________________
View my fuel log 2015 Mirage ES 1.2 manual: 49.6 mpg (US) ... 21.1 km/L ... 4.7 L/100 km ... 59.5 mpg (Imp)
Well, there are several variables here.
1. I don't know all the various OBD-II readers out there.
2. I don't know what reader you are using and what it is capable of. Perhaps you could tell us what it is and what it does?
3. I don't know what code you are chasing. Typically emissions related codes will store data. At least that's my understanding. Other failures may be handled differently, according to the manufacturer.
__________________________________________
View my fuel log 2015 Mirage ES 1.2 manual: 49.6 mpg (US) ... 21.1 km/L ... 4.7 L/100 km ... 59.5 mpg (Imp)
I use this https://www.auteltech.com/Discontinu...ucts/515.jhtml
I see it’s discontinued but they still provide updates regularly.
__________________________________________
View my fuel log 2014 Mirage SE wussie cvt edition. 1.2 automatic: 37.7 mpg (US) ... 16.0 km/L ... 6.2 L/100 km ... 45.3 mpg (Imp)