LetItMarinate (06-04-2018)
stevedmc has a manual transmission, so RPM will be the same (assuming stock tire size) as in:
Thread: Gear ratios: 2014 Mirage transmissions, 5-spd manual & CVT (speed vs. RPM chart)
__________________________________________
View my fuel log 2014 Mirage ES 1.2 manual: 62.4 mpg (US) ... 26.5 km/L ... 3.8 L/100 km ... 74.9 mpg (Imp)
Incidentally, I verified my Rostra cruise control speed isn't based on RPM with a very simply test.
In fifth gear I set my speed with the cruise control to 55 mph. I drove for a moment and then tapped my brakes to disable the cruise control. I then put the vehicle into fourth gear and hit the resume button the the cruise control. It cruised at 55 mph.
Thats a good enough test for me and it verifies that it is using a speed signal from the OBDII port and not RPM information.
__________________________________________
View my fuel log 2015 Mirage ES 1.2 manual: 49.6 mpg (US) ... 21.1 km/L ... 4.7 L/100 km ... 59.5 mpg (Imp)
I'm the kind of person who, when I find a problem too challenging, I walk away from it...at least for a little while. Today, I revistied the problem with getting the ETACS decoder program working on my system. I found I had TOO MANY of the X-Horse drivers installed...apparently Windows doesn't prevent you from installing multiple instances of one driver, but when you do, none of them work. I deleted all of them. I also deleted the manufacturer specific drivers for my MVCI cable.
I downloaded the latest version of the ETACS decoder program and THEIR driver for the MVCI cable and the X-Horse drivers.
I tried to install the X-Horse drivers, but they woudn't install. I DID install the MVCI cable driver with no problems.
I decided to go ahead and try running ETACS decoder and see what happens. It found the cable and I was able to set the COM port and CAN settings, no problem. But, the program was not able to connect to the server to log me in - my firewall was blocking it. I set the firewall to allow ETACS to communicate with the server and I still had 5 writes allowed.
I hauled my computer out to my car, plugged the cable into the OBD port, turned on the ignition, and clicked the 'ON' button on the ETACS display. IT CONNECTED!!!! I then clicked on the 'Engine' tab and all the ETACS items were there; I scrolled down to the Cruise Control setting, changed it to 'Present', clicked on 'Write to ECU' and followed the pop-up instructions. IT WORKED!!!
I disconnected my computer from my car, and took the car for a test drive...I HAVE CRUISE CONTROL!!! (But no horn).
So, I'm happy. A little more tweaking to get the horn working and button everything back up; future plans to enable the fog lights, and disable the engine immobilizer; and maybe I'll just see what kind of trouble I can get into.
Thank you DOAX, and others, for making this possible.
__________________________________________
View my fuel log 2015 Mirage ES 1.2 manual: 49.6 mpg (US) ... 21.1 km/L ... 4.7 L/100 km ... 59.5 mpg (Imp)
Glad to hear you figured it out!
__________________________________________
View my fuel log 2014 Mirage ES 1.2 manual: 62.4 mpg (US) ... 26.5 km/L ... 3.8 L/100 km ... 74.9 mpg (Imp)
Woohoo, very glad to hear you got it figured out.
They must have changed the wiring on the 2017+ models. The only other wires on my connector are for audio controls. The horn is on a different connector.
Custom Mirage products: Cruise control kit, Glove box light, MAF sensor housing, Rear sway bar, Upper grill block
Current project: DIY Nitrous oxide setup for ~$100
__________________________________________
View my fuel log 2015 Mirage DE 1.2 manual: 47.2 mpg (US) ... 20.1 km/L ... 5.0 L/100 km ... 56.7 mpg (Imp)