Results 1 to 10 of 55

Thread: My First car :: 2018 Mitsubishi Mirage ES Plus (Garage entry)

  1. General Information
    My First car
    2018
    Mitsubishi
    Mirage ES Plus
    White
    CVT

    -EZ lip pro side skirt and bumper lip
    -Auto dynasty/Speed Daddy lowering springs
    -Enkei RPF1 15x7 41mm offset
    -Nexen SU1 summer tires 195 45 R15
    -Carbon fibre wrapped hood, VVIVID brand
    -Shark fin antenna
    -Titanium Lug nuts 13g each
    -5% rear passenger window tints. 25% VLT front driver sides. VVIVID tints
    -Rear universal diffuser.
    -underbody rubberize rust coat, partially done. Its an ongoing project.
    -painted the calipers with annonized high heat glossy red
    -Speed Daddy Ebay Springs (FOR SALE!)
    -installed a philips engine block heater
    NOTE: all upgrades were installed by myself. Except tire to rims install and balancing. I did the tints, hood wrap, diffuser install, antenna swap, Underbody rubberized rust coat... etc

    Details

    -Rear diffuser
    https://rover.ebay.com/rover/0/0/0?m...2F182951733803

    -ez lip on the side and front bumper
    https://www.ezlip.com/product/ez-lip-pro/

    -Carbon Hood wrap and gas cover.
    https://www.amazon.ca/gp/product/B00L9J4L6A/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

    -Shark fin antenna installed
    https://www.ebay.ca/itm/White-Auto-Car-Exterior-Roof-Shark-Fin-AM-FM-Radio-RV-Signal-Aerial-Antenna/153056237463?hash=item23a2dcd797:g:j1EAAOSwnTpbHE3 h

    -Vvivid 5% tints and 25% tints high quality, Made in Canada: https://www.ebay.ca/sch/instawraps/m.html?_nkw=&_armrs=1&_ipg=&_from=

    -Led Lights (Headlights, license plate, reverse lights, daytime running light)

    -Vortex generator fins sticked on the spoiler.

    -Benen rear tow hook

    -Rear Stepsill

    Mirage floor mats
    Dashboard cover
    Led dome light 31mm

    Stock Head unit with android auto display
    JBL GTO629 180W front
    JBL GX602 180W rear

    -Sprayed rubberized undercoating in the wheel wells, and underneath the car too.

    -Engine block heater

    -Red annonized metalic caliper painted

    -K&N RG-1001RD Air filter

    -Mobil 1 Extended performance with m1-110 oil filter

    -CVT fluid from Canadian tire
    https://www.canadiantire.ca/en/pdp/oem-synthetic-cvt-asian-atf-946-ml-0281543p.html#srp

    -Rear Resonator delete

    -Godspeed coilovers
    -Daox rear Antiroll bar/Sway Bar
    -eibach Coilovers protector cover

    -Titanium lug nuts
    https://www.twmperformance.com/lug-nuts/titanium-lug-nuts

    (2018)
    -Enkei RPF1 15x7 41mm offset
    -Nexen SU1 summer tires 195 45 R15
    (2019)
    -185/65R14 winter tires with 3mm hub-centric front wheel spacer
    -plastidip wheel covers
    -165/65R14 stock ensave with 25mm hubcentric wheel spacers
    -Rear Fender rolled

    Comments: 54 / Views: 50543

Threaded View

Previous Post Previous Post   Next Post Next Post
  1. #24
    Member Alemon's Avatar
    Join Date
    May 2018
    Location
    ON
    Country
    Canada
    Posts
    65
    Thanks
    8
    Thanked 33 Times in 18 Posts

    Replaced the brake pads at 97,500km & Powerstop Z23 review

    Installed my new brake pads at 97,500 Km with the Powerstop Z23 Carbon Ceramic Pads. The brake pads is noticeably better than stock. It has better bite when braking. The brakes feels stronger when theyre warmed up but still very consistent feeling Through out the de acceleration until stopped.. Theyre very quiet brakes and I am very satisfied with this product. I heard from other reviews that they produce very low unnoticeable dust but I can’t tell since I have my winter steel wheels on. They’re very light brake pads compared to fully ceramic or semi-mettalic pads. The only minor issue is that the two notches on the plate of outer facing pad doesn’t go in the holes of the caliper by hand, or as easily as the OEM. I got around this by using a C Clamp by forcing it in the caliper. It might be hard to remove when the pads are due, but I put an anti seize to make it easier to uninstall. If anyone knows the min rotor thickness, please let me know. The imprint on the backing of the rotors is rusted from Canadian winter.
    Attached Images Attached Images  
    Last edited by Alemon; 02-22-2020 at 11:49 AM.

  2. The Following User Says Thank You to Alemon For This Useful Post:

    MetroMPG (02-22-2020)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •